Troubleshooting table If… Then check … neither echo nor battery voltage. Position the second cable clamphalfway between the first clamp andthe cable hole.
Set range of each of the eight basicranges. Apply a sufficient amount of high quality caulking compound to the top surface of the transducer, around the threads of the stuffing tube and inside the mounting hole and fairing Fire or electrical shock can result if thepower is left on.
Troubleshooting tableIf…neither echo norfixed range scaleappearsno echo appearsbut the fixedrange scaleappears1. Single frequency displayDual frequency display50 kHzThe 50 kHz picture appears on the left;the kHz picture on the right. This mode is useful for determining bottom contour. All default basic ranges arerestored whenever the depth unit ischanged. Carefully remove anymarine life with a piece of wood orfine-grade sandpaper.
This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website.
We also use third-party cookies that help us analyze and understand how you use this website. This may require a certain amount of experimentation for fine tuning at high cruising speeds.
Fill the gap between the wedge front of the transducer and transom with epoxy material to eliminate any air spaces. Necessary tools You will need the following tools: Sandpaper Silicone sealant Silicone grease Remarks on installation Page Optional Triducer 3. Mounting location To ensure the best performance, the sensor must be submerged in aeration-free and turbulence-free water. Mount the sensor close to the centerline of the boat.
Page 37 Warning: Always wear safety goggles and a dust mask. Page 38 4. Repeat step 1 to ensure that the angle of the sensor is correct.
Note: Do not position the sensor farther into the water than necessary to avoid increasing drag, spray, and water noise and reducing boat speed. Position the second cable clamp halfway between the first clamp and the cable hole. Mark this mounting hole. If a hole has been drilled in the transom, open the appropriate slot in the transom cable cover.
Position the cover over the cable where it enters the hull. Page Wiring Coat with silicone sealant. Refer to the interconnection diagram to connect cables. Leave slack in cables to facilitate checking and maintenance. Page Iec Data Sentences 4. The transmission speed for both input and output is bps.
Data is output at two-second intervals. Input data sentences Page Installation Menu Choose On to output input data. Off: Outputs the data sentences of LS only. On: Outputs the data sentences of LS and sentences which are input from other equipment. To restore normal operation, turn off the power and then turn it on again. Find the marine product manual you need at ManualsOnline.
Page 1. Ls — read user manual online or download in PDF format. Pages in total: en este manual. The cursorappears along with waypoint entryinstructions.
To suppress interference, do the following: There are no uer-serviceable partsinside. Therefore, the 50 kHzfrequency is useful for general detectionand judging bottom condition.
Page 36 Transom hole: Outputs the data sentences of LS and sentences which are input from other equipment. MENU from page 2 on the menu. Appearance of weak echoes These weak echoes may be manial as follows: Coat with silicone sealant.
Choose the water typewith which to use the LS, fromSalt or Fresh. Therefore, the 50 kHz frequency is useful for general detection and judging bottom condition. The installer of the equipment is solely responsible for the proper furhno of the equipment. Iec Data Sentences 4. Page 25 Requires appropriate nav data.
Comprised of a display unit and atransducer, the LS displaysunderwater conditions on a bright 5-inchmonochrome LCD. Lower HalfSaw along slopeof hull. Keep the display unit fuuno of direct sunlight. Fish school clearly shown White line The display unit can be installed on adesktop, on the bulkhead or flushmounted in a panel.
The auto mode in use is shown as Auto-Fishing or Auto-Cruising at the top left corner on the screen. This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website.
We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies.
But opting out of some of these cookies may have an effect on your browsing experience. Necessary cookies are absolutely essential for the website to function properly.
0コメント